301.10 no model and sw version error

bittug · Post by **bittug** » Mon Jan 10, 2011 4:26 pm

i read both tsop of 301.10 with usb jtag and opened in flashedit i dont see model # and sw version in the filelds?

bittug · Post by **bittug** » Tue Jan 11, 2011 3:04 pm

here is a out put it didnt detect the flas type.do i need to edit config?

Copyright (C) 2010,2011,2012
USB JTAG NT 0.43
Target: DP301-010
-detect
IDCODE 5400006D
LSI SC2000
IMPCODE 01B71700
EJTAG V2.6
DMA supoorted
Found Address= 9fc00000 AMD 29lv160DB
Found Address= 9fe00000 AMD 29lv160DB
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum 0000,0000

Post by **usbbdm** » Tue Jan 11, 2011 4:18 pm

bittug wrote:here is a out put it didnt detect the flas type.do i need to edit config?

Copyright (C) 2010,2011,2012
USB JTAG NT 0.43
Target: DP301-010
-detect
IDCODE 5400006D
LSI SC2000
IMPCODE 01B71700
EJTAG V2.6
DMA supoorted
Found Address= 9fc00000 AMD 29lv160DB
Found Address= 9fe00000 AMD 29lv160DB
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum 0000,0000

Can you post the xml file?

bittug · Post by **bittug** » Wed Jan 12, 2011 5:56 am

DP301-010DishIrdEJTAGLittle0xBE2500005Yes00x80020000Ram00x800000000x800000U2310x9FC000000x200000U2210x9FE000000x1F0000Eeprom20x00x800

Post by **usbbdm** » Wed Jan 12, 2011 9:07 am

bittug wrote:DP301-010DishIrdEJTAGLittle0xBE2500005Yes00x80020000Ram00x800000000x800000U2310x9FC000000x200000U2210x9FE000000x1F0000Eeprom20x00x800

I have not tested this box with NT software. Maybe I need to find the box from the closet and test again. Sorry I need to travel and may not have time to test this box for two weeks.

Post by **usbbdm** » Wed Jan 12, 2011 12:09 pm

I will see if I can squeeze some time tonight to test this box.

Post by **usbbdm** » Thu Jan 13, 2011 8:34 pm

OK. I opened this box today and found some bug.The issue related to the EEPROM code that was broken. It is unlikely I will fix it today. You have to wait for my next release to fix this issue.

bittug · Post by **bittug** » Fri Jan 14, 2011 5:34 am

sure thanks

Post by **usbbdm** » Fri Jan 14, 2011 9:07 am

bittug wrote:sure thanks

The known issues now is
"getram" for eeprom will not work if you read all. If you read 256 bytes at a time it will work.
For EEPROM you have to use 6M clock or less to program.
I will send you a test load once I build a newer one before I officially upload. I will also test 013 this time since it might also be broken.

bittug · Post by **bittug** » Fri Jan 14, 2011 10:12 am

i dont need to read eeprom i need only u23 read and write?

Post by **usbbdm** » Sat Jan 15, 2011 3:48 am

Read is perfect for U23 and U22. As of write it should also have no issue. Just ignore the error for the flash. It did extra check for EEPROM as flash (BUG)

bittug · Post by **bittug** » Sat Jan 15, 2011 6:21 am

i tried to write u23 it was stuck at erase walf of the way.and then it bricked ord?

Post by **usbbdm** » Sat Jan 15, 2011 10:53 am

Then try to use erase and sprogram. will do a full programming myself after I come back. I already fixed the EEPROM read/write. I am not happy with it and would like to use 12MHz. So I need to re-write the firmware.

bittug · Post by **bittug** » Sat Jan 15, 2011 1:44 pm

i used parllel port jtag and fixed it.but usb jtag realy needs to be fixed

Post by **usbbdm** » Sat Jan 15, 2011 3:52 pm

OK no problem. Also will test on 013 too.

301.10 no model and sw version error

301.10 no model and sw version error

Who is online