Please post anything that you need to debrick in here.

[dyno58]

Anyone have a full working dump for it ???? or can help me debrick my wrt54gs v4 ethernet lights all are steady on, and the power light blinking

Thanks in advance

[cyberhome08]

anyone have a vision 0.24 usb jtag debricking sb 5101 .please i have has buy from this usb jtag i has 0.26 but i saw a video they debrick a0.24 , i has send amail to [email protected] m it nothing . and i contrat with usbbdm until no response my a-mail . what the deal mr usbbdm ?

[usbbdm]

Anything 0.24 can do can be done with 0.29. There is not need to go back to old version.
The way to debrick has not changed from 0.24 to 0.29. Normally I do not encourage to use any older version of software. (I have seen people still use 0.05 software).

I know we can heavily brick SB5100 with hoxware programmed 2M to SB5100. (I did myself). This brick cannot be debricked with debrick command. I am still searching a more reliable way to debrick it. So far not much lucky yet other than the 3.3V aand CE method.

[cyberhome08]

Anything 0.24 can do can be done with 0.29. There is not need to go back to old version.
The way to debrick has not changed from 0.24 to 0.29. Normally I do not encourage to use any older version of software. (I have seen people still use 0.05 software).

I know we can heavily brick SB5100 with hoxware programmed 2M to SB5100. (I did myself). This brick cannot be debricked with debrick command. I am still searching a more reliable way to debrick it. So far not much lucky yet other than the 3.3V aand CE method.

thanks mr usbbdm you reply post . it 0.29 do the same debrick command 0.24 .

[Gordy420]

I bricked my RTP300 upgrading firmware through browser,now router only shows steady power light and cant ping it.Any chances of getting def file for Linksys RTP300?Thanks in advance

Texas Instruments
Spansion chip set
S29GL064M90TAIR4
I get this below if i use wrt54gs or v2 config

-detect
IDCODE B52D02F
Manufacturer not found 017

[usbbdm]

I have not tested this device. Are you sure this is MISP core (Broadcom, TI etc). If it is MIPS core, there is a big chance the UBSJTAG (NT) can fix it. If it is not, theew is no short plan to support other CPUs as I have too many device to test on. So go to the board and find the main CPU, post the CPU. In the mean time I will do some search about your device.

[usbbdm]

I confirm that this is a MIPS core and USBJTAG (NT) should support this device. I will try to get one of this device this weekend and post how to JTAG it.

[Gordy420]

I confirm that this is a MIPS core and USBJTAG (NT) should support this device. I will try to get one of this device this weekend and post how to JTAG it.

CPU says
TNETV1060GDW
56P6568

Thanks for looking into his.

[usbbdm]

I got my new RTP300 today. Here is what I read with USBJTAG NT.
detect
IDCODE 0B52D02F
TI1 TNETV10552
IMPCODE 41404000
DMA not supoorted
Found Address= 90000000 AMD 29lv320MT
I will see how to make USBJTAG NT to unlock it. I think the same method will unlock VT2442 which I also have one.

[usbbdm]

See my other thread.
viewtopic.php?t=2674

[bor154311]

If you do not have a JTAG you need to replace the TSOP flash.

I have parajtag is`t enough for improve sitation?

[usbbdm]

If you use pjtag you can unlock it but only use pjtag to write the boot to enable serial port. Than you need a cable to connect RS232 (Make the level convert with MAX chip), you then use TFTP to downgrade the firmware, then use the CYT tool to unlock the password.
Then you can go to VOIP setting.

With USB JTAG NT, you can bypass the serial port as the NT programs much faster than TFTP downloading.

[shappyking]

this guy is spamming every thread

[konnan]

Master USBBDM Bann this guy lyjg1129 he is spamming us..

[xy-Zee]

can i debrick a 5120 with the usbjtag NT? and how?