/////////////////////////////////////////////
// SB6120 Script
/////////////////////////////////////////////
1. Backup flash
2. Restore flash
3. Program boot (Like noisy boot)
4. Program firmware (Like shell firmware
5. Exit
Please select
2
-flshdct 0
Found Address= 00000000 25FL064A
-ldram 0
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/copia SB6120/00000000.bin loaded
-program 0 800000
Erase starts...
Erase time 00:00:52 (.969)
Program Starts...
Program speed 236.61 KB/s
Program time 00:00:35 (.453)
Program pass, if no further programming needed, power off/on the target
-cmpram 0 800000
Compare data Failed address 2A01,target 8E,PC memory 87
Time 00:00:08 (.953)
Press enter to continue.Spacebar and enter to break....
mi modem ahora no arranca solo se queda encendida la primera luz, le estoy metiendo el respaldo que previamente le saqué.
Debrick SB6120
-
- Junior Member
- Posts: 8962
- Joined: Mon Jul 18, 2005 9:33 pm
Try to use speed 1 or speed 2 to see if it works.softrend wrote://///////////////////////////////////////////
// SB6120 Script
/////////////////////////////////////////////
1. Backup flash
2. Restore flash
3. Program boot (Like noisy boot)
4. Program firmware (Like shell firmware
5. Exit
Please select
2
-flshdct 0
Found Address= 00000000 25FL064A
-ldram 0
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/copia SB6120/00000000.bin loaded
-program 0 800000
Erase starts...
Erase time 00:00:52 (.969)
Program Starts...
Program speed 236.61 KB/s
Program time 00:00:35 (.453)
Program pass, if no further programming needed, power off/on the target
-cmpram 0 800000
Compare data Failed address 2A01,target 8E,PC memory 87
Time 00:00:08 (.953)
Press enter to continue.Spacebar and enter to break....
mi modem ahora no arranca solo se queda encendida la primera luz, le estoy metiendo el respaldo que previamente le saqué.
Make sure ground is connected properly.
-
- Junior Member
- Posts: 68
- Joined: Fri Oct 13, 2006 12:16 pm
no yet
/////////////////////////////////////////////
// SB6120 Script
/////////////////////////////////////////////
1. Backup flash
2. Restore flash
3. Program boot (Like noisy boot)
4. Program firmware (Like shell firmware
5. Exit
Please select
2
-flshdct 0
Found Address= 00000000 25FL064A
-ldram 0
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/copia SB6120/00000000.bin loaded
-program 0 800000
Erase starts...
Erase time 00:00:54 (.266)
Program Starts...
Program speed 162.64 KB/s
Program time 00:00:51 (.578)
Program pass, if no further programming needed, power off/on the target
-cmpram 0 800000
Time 00:00:35 (.329)
Compare data OK
Press enter to continue.Spacebar and enter to break....
En speed 2 no marca error, pero aun sigue solo con el primer led encendido
LISTO
Copyright (C) 2010,2011,2012
USB JTAG NT 0.46
Target: SB6120
-flshdct 0
Found Address= 00000000 25FL064A
-ldram U-Boot
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/SB6120/SB6120_Noisy_Bootloader.bin loaded
-program U-Boot
Erase starts...
Erase time 00:00:00 (.812)
Program Starts...
Program speed 190.51 KB/s
Program time 00:00:00 (.688)
Program pass, if no further programming needed, power off/on the target
-speed 2
-ldram UBFI1
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/SB6120/SBH_Alpha1.0.0-BPI_DISABLED.bin loaded
-ldram UBFI2
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/SB6120/SBH_Alpha1.0.0-BPI_DISABLED.bin loaded
-program UBFI2
Erase starts...
Erase time 00:00:25 (.156)
Program Starts...
Program speed 155.34 KB/s
Program time 00:00:24 (.891)
Program pass, if no further programming needed, power off/on the target
-cmpram UBFI2
Time 00:00:16 (.312)
Compare data OK
-program UBFI1
Erase starts...
Erase time 00:00:25 (.328)
Program Starts...
Program speed 155.15 KB/s
Program time 00:00:24 (.922)
Program pass, if no further programming needed, power off/on the target
-cmpram UBFI1
Time 00:00:16 (.296)
Compare data OK
My Modem Is Alive again, Thanks Alot
// SB6120 Script
/////////////////////////////////////////////
1. Backup flash
2. Restore flash
3. Program boot (Like noisy boot)
4. Program firmware (Like shell firmware
5. Exit
Please select
2
-flshdct 0
Found Address= 00000000 25FL064A
-ldram 0
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/copia SB6120/00000000.bin loaded
-program 0 800000
Erase starts...
Erase time 00:00:54 (.266)
Program Starts...
Program speed 162.64 KB/s
Program time 00:00:51 (.578)
Program pass, if no further programming needed, power off/on the target
-cmpram 0 800000
Time 00:00:35 (.329)
Compare data OK
Press enter to continue.Spacebar and enter to break....
En speed 2 no marca error, pero aun sigue solo con el primer led encendido
LISTO
Copyright (C) 2010,2011,2012
USB JTAG NT 0.46
Target: SB6120
-flshdct 0
Found Address= 00000000 25FL064A
-ldram U-Boot
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/SB6120/SB6120_Noisy_Bootloader.bin loaded
-program U-Boot
Erase starts...
Erase time 00:00:00 (.812)
Program Starts...
Program speed 190.51 KB/s
Program time 00:00:00 (.688)
Program pass, if no further programming needed, power off/on the target
-speed 2
-ldram UBFI1
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/SB6120/SBH_Alpha1.0.0-BPI_DISABLED.bin loaded
-ldram UBFI2
C:/Documents and Settings/Sistemas/Escritorio/Respaldo 500/usbjtag/Script.Intuitivo.by.SaNTy-R1.v1.0.Final/SB6120/SBH_Alpha1.0.0-BPI_DISABLED.bin loaded
-program UBFI2
Erase starts...
Erase time 00:00:25 (.156)
Program Starts...
Program speed 155.34 KB/s
Program time 00:00:24 (.891)
Program pass, if no further programming needed, power off/on the target
-cmpram UBFI2
Time 00:00:16 (.312)
Compare data OK
-program UBFI1
Erase starts...
Erase time 00:00:25 (.328)
Program Starts...
Program speed 155.15 KB/s
Program time 00:00:24 (.922)
Program pass, if no further programming needed, power off/on the target
-cmpram UBFI1
Time 00:00:16 (.296)
Compare data OK
My Modem Is Alive again, Thanks Alot
Who is online
Users browsing this forum: No registered users and 5 guests