ECU IAW48P
-
- Junior Member
- Posts: 5
- Joined: Mon Jul 13, 2020 9:53 am
ECU IAW48P
Dear Sir!
Can u help me to make right config for my ecu?
I tryed all possible bdm targets without success.
Target CPU is: MC68376, Flash is AMD 29F200BB, EEP is Atmel25080
Copyright (C) 2010-2025
USB BDM NT 1.11
Target: AUDITCU256
-speed 0
-speed 1
-reset 1
Unknown flash type!
Report these values http://www.usbjtag.com/phpbb3 0004h,1e00h
regards
Gabor
ps: played with it, i can read the whole flash well using -getram 40000 40000, only byte order differ if flash desoldered and readed with flash programmer
Can u help me to make right config for my ecu?
I tryed all possible bdm targets without success.
Target CPU is: MC68376, Flash is AMD 29F200BB, EEP is Atmel25080
Copyright (C) 2010-2025
USB BDM NT 1.11
Target: AUDITCU256
-speed 0
-speed 1
-reset 1
Unknown flash type!
Report these values http://www.usbjtag.com/phpbb3 0004h,1e00h
regards
Gabor
ps: played with it, i can read the whole flash well using -getram 40000 40000, only byte order differ if flash desoldered and readed with flash programmer
You do not have the required permissions to view the files attached to this post.
-
- Junior Member
- Posts: 5
- Joined: Mon Jul 13, 2020 9:53 am
Re: ECU IAW48P
Forget to add dump.
You do not have the required permissions to view the files attached to this post.
-
- Junior Member
- Posts: 8962
- Joined: Mon Jul 18, 2005 9:33 pm
Re: ECU IAW48P
I am willing to help you.
1. When you read the flash, do you use BDM NT to read the flash or you use a programmer?
2. Are you sure this is MC6833X CPU and you are sure the BDM pinout is correct?
I can disassemble the firmware and analyze the initialization then create the XML.
It is better we work together and I am using zoom meeting now to remote desktop your pc.
1. When you read the flash, do you use BDM NT to read the flash or you use a programmer?
2. Are you sure this is MC6833X CPU and you are sure the BDM pinout is correct?
I can disassemble the firmware and analyze the initialization then create the XML.
It is better we work together and I am using zoom meeting now to remote desktop your pc.
-
- Junior Member
- Posts: 5
- Joined: Mon Jul 13, 2020 9:53 am
Re: ECU IAW48P
Hi!
1. I readed flash with flash programmer also with BDM NT too.The attahced dump is readed with BDM NT, used TAUDITCU256.xml and -getram 40000 40000. The two readout is 100% equal, only issue that bdm readout had swapped bytes.
2. Im 100% sure about CPU type Volvo CEM had same CPU and same mask number 0F71K , there is no standard bdm header on board , but i found pins myself from MC68336376UM.pdf documentation.
Also i tryed to add flash type myself to database without success , tryed id1=01 id2=57 or id1=01 id2=2257 found page 17 of
29F200BB datasheet at https://www.ret.hu/media/product/12546/ ... EC-AMD.pdf,
1. I readed flash with flash programmer also with BDM NT too.The attahced dump is readed with BDM NT, used TAUDITCU256.xml and -getram 40000 40000. The two readout is 100% equal, only issue that bdm readout had swapped bytes.
2. Im 100% sure about CPU type Volvo CEM had same CPU and same mask number 0F71K , there is no standard bdm header on board , but i found pins myself from MC68336376UM.pdf documentation.
Also i tryed to add flash type myself to database without success , tryed id1=01 id2=57 or id1=01 id2=2257 found page 17 of
29F200BB datasheet at https://www.ret.hu/media/product/12546/ ... EC-AMD.pdf,
-
- Junior Member
- Posts: 8962
- Joined: Mon Jul 18, 2005 9:33 pm
Re: ECU IAW48P
1. USB BDM NT read out is correct. Your programmer has the data swapped.
2. You need to read start from 0 to be able to disassemble properly.
2. You need to read start from 0 to be able to disassemble properly.
-
- Junior Member
- Posts: 5
- Joined: Mon Jul 13, 2020 9:53 am
Re: ECU IAW48P
Hi!
Attached read 0 and read 40000.
Read 0 is bad, the first 8k is wrong. Read 40000 perfect its same as read with flash programmer , probably XML not for this ecu (TAUDITCU256).
Please help make right XML read FLASH from address 0 also find how to read EEP well, becouse EEP read is 00 ff 00 ff .
regards
Gabor
Attached read 0 and read 40000.
Read 0 is bad, the first 8k is wrong. Read 40000 perfect its same as read with flash programmer , probably XML not for this ecu (TAUDITCU256).
Please help make right XML read FLASH from address 0 also find how to read EEP well, becouse EEP read is 00 ff 00 ff .
regards
Gabor
You do not have the required permissions to view the files attached to this post.
-
- Junior Member
- Posts: 8962
- Joined: Mon Jul 18, 2005 9:33 pm
Re: ECU IAW48P
I disassemble your 000000.bin and the the program seems wrong in a reboot loop.
Are you sure this is a working unit? You should better use online chat instead asking on this forum.
Forum is used to discuss issue. Asking online help on the forum will not work well for you.
Are you sure this is a working unit? You should better use online chat instead asking on this forum.
Forum is used to discuss issue. Asking online help on the forum will not work well for you.
-
- Junior Member
- Posts: 5
- Joined: Mon Jul 13, 2020 9:53 am
Re: ECU IAW48P
Hi!
Please disassembly 40000.bin becouse i told 00000.bin is wrong.
I can online from saturdays .
Thank you
Regards
Gabor
Please disassembly 40000.bin becouse i told 00000.bin is wrong.
I can online from saturdays .
Thank you
Regards
Gabor
-
- Junior Member
- Posts: 8962
- Joined: Mon Jul 18, 2005 9:33 pm
Re: ECU IAW48P
It is important to have 0000 right to be able to find the init sequence. Let us do it while online.
-
- Junior Member
- Posts: 8962
- Joined: Mon Jul 18, 2005 9:33 pm
Re: ECU IAW48P
25080 is another flash with SPI protocol. It needs to either read via u-Link NT or write program to read/write this via BDM NT.
Who is online
Users browsing this forum: No registered users and 4 guests