WatchDog/Hunt
-
- Junior Member
- Posts: 65
- Joined: Fri Nov 09, 2007 4:23 am
No UA Change
I tested another unit and it kept the same UA. It was able to be hit by the dac. So this may not help in the UA cause. Sorry....
-
- Junior Member
- Posts: 268
- Joined: Sat Jun 07, 2008 2:56 pm
you did not chaned the uid just because you program box. the box was e11 thats why. also plat is only hting you can program ..tvguide and specially vod app is hardest... they are at the end were the watchdog is in place.../ the nvram will disable them if are not initialized at first boot. many other problems
do not believe what i say 10% its true
-
- Junior Member
- Posts: 268
- Joined: Sat Jun 07, 2008 2:56 pm
-
- Junior Member
- Posts: 65
- Joined: Fri Nov 09, 2007 4:23 am
Channel Map
I have the same channels as the one I got the files from. I have high def, digital and analog. The dac I am testing with does not have encrypted channels so I can't say if that would work. This worked on a E11 box too. I have not been able to enable dvr funtion, but I am still working on that problem this week.
-
- Junior Member
- Posts: 65
- Joined: Fri Nov 09, 2007 4:23 am
Dvr
I was able to clone the nvram and plat from another box. I got tv_guide, hd, digital, analog and dvr. It did not need initialized from the dac. I had to pull the memory from the host unit many many times. It took over a hour to install on the new unit. I have a couple more to test tomorrow.
-
- Junior Member
- Posts: 65
- Joined: Fri Nov 09, 2007 4:23 am
Tested
I have tested three more units. I was able to load TC_CS_CC, Tv_Guide and S_SECVO. The DVR records. The channels map is the same as host unit. I programed the plat backwards.
9CBC0000 3E0000
(POWER RESET)
DETECT
9C7E0000 3E0000
(POWER RESET)
DETECT
9C400000 3E0000
(POWER RESET)
DETECT
9C200000 200000
(POWER RESET)
DETECT
9C020000 100000
(POWER RESET)
DETECT
CMPRAM PLAT
(POWER RESET)
DETECT
SETRAM NVRAM
The unit should now load all apps after reboot (of course you must load the plat and nvram into the jtag software)
9CBC0000 3E0000
(POWER RESET)
DETECT
9C7E0000 3E0000
(POWER RESET)
DETECT
9C400000 3E0000
(POWER RESET)
DETECT
9C200000 200000
(POWER RESET)
DETECT
9C020000 100000
(POWER RESET)
DETECT
CMPRAM PLAT
(POWER RESET)
DETECT
SETRAM NVRAM
The unit should now load all apps after reboot (of course you must load the plat and nvram into the jtag software)
-
- Junior Member
- Posts: 32
- Joined: Fri Dec 12, 2008 9:20 am
another phase of DCT6412
i am trying to see if we i can do the same thing with another phase of DCT6000 and see what happened, keep up the good work guys.
-
- Junior Member
- Posts: 133
- Joined: Mon Feb 08, 2010 9:47 am
I am trying to load old PLAT, APP1 and NVRAM but keep getting error. Here is my log from NT.
Copyright (C) 2010,2011,2012
USB JTAG NT 0.45b
Target: DCT6412
C:/UsbJtag/6412/Nvram.bin loaded
Do not forget to set the NVRAM
C:/UsbJtag/6412/Plat.bin loaded
C:/UsbJtag/6412/APP1.BIN loaded
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9CBC0000 3E0000
Erase starts...
Erase time 00:00:20 (.605)
Program speed 674.28 KB/s
Program time 00:00:06 (.027)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C7E0000 3E0000
Erase starts...
Erase time 00:00:19 (.341)
Program speed 674.28 KB/s
Program time 00:00:06 (.026)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C400000 3E0000
Erase starts...
Erase time 00:00:18 (.963)
Program speed 259.40 KB/s
Program time 00:00:15 (.665)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C200000 200000
Erase starts...
Erase time 00:00:10 (.580)
Program speed 139.74 KB/s
Program time 00:00:15 (.009)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C020000 100000
Erase starts...
Erase time 00:00:05 (.467)
Program speed 140.52 KB/s
Program time 00:00:07 (.464)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-CMPRAM PLAT
Time 00:00:10 (.877)
Compare data Failed address 9C120000,target 33,PC memory 39
Copyright (C) 2010,2011,2012
USB JTAG NT 0.45b
Target: DCT6412
C:/UsbJtag/6412/Nvram.bin loaded
Do not forget to set the NVRAM
C:/UsbJtag/6412/Plat.bin loaded
C:/UsbJtag/6412/APP1.BIN loaded
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9CBC0000 3E0000
Erase starts...
Erase time 00:00:20 (.605)
Program speed 674.28 KB/s
Program time 00:00:06 (.027)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C7E0000 3E0000
Erase starts...
Erase time 00:00:19 (.341)
Program speed 674.28 KB/s
Program time 00:00:06 (.026)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C400000 3E0000
Erase starts...
Erase time 00:00:18 (.963)
Program speed 259.40 KB/s
Program time 00:00:15 (.665)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C200000 200000
Erase starts...
Erase time 00:00:10 (.580)
Program speed 139.74 KB/s
Program time 00:00:15 (.009)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C020000 100000
Erase starts...
Erase time 00:00:05 (.467)
Program speed 140.52 KB/s
Program time 00:00:07 (.464)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-CMPRAM PLAT
Time 00:00:10 (.877)
Compare data Failed address 9C120000,target 33,PC memory 39
-
- Junior Member
- Posts: 1417
- Joined: Wed Jan 28, 2009 4:01 pm
you should have started up a new thread instead of bringing one up from 2009!!ilavu wrote:I am trying to load old PLAT, APP1 and NVRAM but keep getting error. Here is my log from NT.
Copyright (C) 2010,2011,2012
USB JTAG NT 0.45b
Target: DCT6412
C:/UsbJtag/6412/Nvram.bin loaded
Do not forget to set the NVRAM
C:/UsbJtag/6412/Plat.bin loaded
C:/UsbJtag/6412/APP1.BIN loaded
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9CBC0000 3E0000
Erase starts...
Erase time 00:00:20 (.605)
Program speed 674.28 KB/s
Program time 00:00:06 (.027)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C7E0000 3E0000
Erase starts...
Erase time 00:00:19 (.341)
Program speed 674.28 KB/s
Program time 00:00:06 (.026)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C400000 3E0000
Erase starts...
Erase time 00:00:18 (.963)
Program speed 259.40 KB/s
Program time 00:00:15 (.665)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C200000 200000
Erase starts...
Erase time 00:00:10 (.580)
Program speed 139.74 KB/s
Program time 00:00:15 (.009)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-program 9C020000 100000
Erase starts...
Erase time 00:00:05 (.467)
Program speed 140.52 KB/s
Program time 00:00:07 (.464)
Program pass, if no further programming needed, power off/on the target
-detect
IDCODE 1703817F
Broadcom BCM7038
IMPCODE 40404001
EJTAG V1, V2.0
DMA not supoorted
Found Address= 9c000000 CFI Intel128
-CMPRAM PLAT
Time 00:00:10 (.877)
Compare data Failed address 9C120000,target 33,PC memory 39
other then that....why don't you try putting in a different command..there is a much easier way of accomplishing what you want to do...instead of programing areas at a time :program 9CBC0000 3E0000: why don't you try to do the whole thing at once? you might get better results
live your life like a beer commericial
Who is online
Users browsing this forum: No registered users and 6 guests