on diagnostic screen is white blue and on modules under options 10 shows vod? ennorun...
since i dont know which type is 1 0r 2 i tried both it is getting unknows flash type after flshdct 400000
-reset 1
-R
-init
-getram 200000 40000
-d 234f09
-reset 1
-R
-init
-ldram 400000 (loaded PH61.ZIP)
-flshdct 400000
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
-R
-reset 1
-R
-init
-getram 200000 40000
-d 234f09
-reset 1
-R
-init
-ldram 400000 (loaded 0793tvr7304rSPI.zip)
Flip Firmware
-flshdct 400000
Unknown flash type!
Report these two value to http://www.usbjtag.com/vbforum ffff,ffff
could you tell me what is wrong??? also i have bdmnt cable and box displays 0 an screen and my problem is anly vod wont load but channels are working.. thx
ph6 no guide
Moderator: justsomeguy
-
- Junior Member
- Posts: 88
- Joined: Fri Apr 11, 2008 5:45 pm
well it wasnt cut. now i cut c105 then run the commands againusbbdm wrote:I wil try to see if you have cut C105. I fyou have a screen capture I might tell more.
Copyright http://www.usbjtag.com 2008,2009,2010
USB BDM NT 0.31
Latest version is 0.32
-R
-reset 1
-init
-R
-getram 200000 40000
-d 234f09
-reset 1
-init
-R
-ldram 400000 (0793tvr7304rSPI)
Flip Firmware
-flshdct 400000
Found Address= 00400000 SHARP LH28F160BJHG
-program 400000 200000
Erase starts...
Erase time 00:00:43 (.093)
Program Starts...
Program speed 49.13 KB/s
Program time 00:00:42 (.859)
Program pass, if no further programming needed, power off/on the target
THIS FOR PH2 DIDNT CHANGE ANYTHING SO I TRIED FOR PH1
-R
-reset 1
-init
-R
-getram 200000 40000
-d 234f09
-reset 1
-init
-R
-ldram 400000 (PH61 ZIP FILE)
-flshdct 400000
Found Address= 00400000 SHARP LH28F160BJHG
-program 406000 aa000
Erase starts...
Erase time 00:00:15 (.718)
Program Starts...
Program speed 41.07 KB/s
Program time 00:00:16 (.781)
Program pass, if no further programming needed, power off/on the target
-program 4c0000 90000
Erase starts...
Erase time 00:00:10 (.859)
Program Starts...
Program speed 72.04 KB/s
Program time 00:00:08 (.156)
Program pass, if no further programming needed, power off/on the target
-ldram 200000
-setram 200000 40000
-R
BUT STILL WHITE BLACK SCREEN ONLY THING CHANGED IS DIAGNOSTIC NO 10 MODULES DCT_ROM IS 05.88 ENABLED AND NO OTHER MODULES Y
ET. I PLUG INTO COAX INPUT TO SEE IF IT LOADS IT SELF BUT SO FAR NOTHING
-
- Junior Member
- Posts: 88
- Joined: Fri Apr 11, 2008 5:45 pm
was already unzipped
usbbdm wrote:You need unzip the file. ZIP file is for downloading purpose.
sorry to not mention was unzipped. also after this programming i lost the digital channels box works only analog mod like with little bit snowy picture not dig mode with only basic channels. and diagnostic screen 10 shows dct rom module and wont load other modules. what should i try next
Who is online
Users browsing this forum: No registered users and 4 guests