unknown flash type? DCT2224

Include DCT cable boxes and Starchoice boxes.

Moderator: justsomeguy

Locked
JDMEGKOUPE
Junior Member
Posts: 19
Joined: Mon Jul 26, 2010 12:41 pm

unknown flash type? DCT2224

Post by JDMEGKOUPE »

-FLSHDCT code
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum 0000,0000

this happens whenever i try to read/ write the code...
is this a firmware issue? its type II firmware ph6/cr4

pic1
Image

which pic shows correct placement?
Uploaded with ImageShack.us

pic2
Image

Uploaded with ImageShack.us
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

JDMEGKOUPE wrote:-FLSHDCT code
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum 0000,0000

this happens whenever i try to read/ write the code...
is this a firmware issue? its type II firmware ph6/cr4

pic1
Image

which pic shows correct placement?
Uploaded with ImageShack.us

pic2
Image

Uploaded with ImageShack.us
1. You need to have proper dll.
2. You need to remove C105.
3, You need to issue command "init"
JDMEGKOUPE
Junior Member
Posts: 19
Joined: Mon Jul 26, 2010 12:41 pm

Post by JDMEGKOUPE »

whats the correct cable placement on this box? the bdm says "connected" & "on" in 3 of the 4 positions possible
d0
Junior Member
Posts: 177
Joined: Thu Feb 26, 2009 9:50 am
Location: S FL
Contact:

Post by d0 »

pin1 on NT goes to pin1 on the box. Pin1 should be a small white circle.
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

JDMEGKOUPE wrote:-FLSHDCT code
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum 0000,0000

this happens whenever i try to read/ write the code...
is this a firmware issue? its type II firmware ph6/cr4

pic1
Image

which pic shows correct placement?
Uploaded with ImageShack.us

pic2
Image

Uploaded with ImageShack.us
Another Important thing to Note. I noticed in the Picture what appears to Be the 14 Pin Connector of a USBJTAG NT If you Intend to program anything to a DCT2224 You Need the USBBDM NT Not the USBJTAG NT. ;)
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
cherrymachine
Junior Member
Posts: 177
Joined: Thu Jul 26, 2007 7:52 am

Post by cherrymachine »

i dont think think its even a 2224 board. Its definitly not a ph6. All the JTAG connctions on a ph 6 7 8 9 are next to the power supply and what it the stud thing on the back. Post a pic of the label on the bottom. Good eye there Tundra
Killswitch
Junior Member
Posts: 439
Joined: Tue Mar 23, 2010 6:12 am

Prehistoric Hardware

Post by Killswitch »

It occurs to me that the boy has a 2224 that's non-ph and an Older board. I could be wrong but I see 2 AMD 29LV800BB flash chips that are pain in the ass just by themselves. And, Tundra's right. He's trying to JTAG the box. Oh,my God! Somebody better set down and start Spoonfeeding this guy. Just kidding! I need a big Silver Soup spoon every now and them to feel full. Somebody best toss him a BDM!
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

http://www.usbjtag.com/dct2000/nonph.php
Then you need BDM NT not JTAG or JTAG NT. It WILL NOT WORK.
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

cherrymachine wrote:i dont think think its even a 2224 board. Its definitly not a ph6. All the JTAG connctions on a ph 6 7 8 9 are next to the power supply and what it the stud thing on the back. Post a pic of the label on the bottom. Good eye there Tundra
It is in fact a DCT2200 Series Box. If you look closely you can count the Pin header has 10 Pins.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
JDMEGKOUPE
Junior Member
Posts: 19
Joined: Mon Jul 26, 2010 12:41 pm

Post by JDMEGKOUPE »

Image

Uploaded with ImageShack.us

im using a usbbdm original, not usbjtag nt, usbjtag, or usbbdm nt... can the original model work?

quick question, i borrowed this tool from a friend and now that u ALL pointed it out... why does it come up as an old BDM in the usbjtag software but it clearly has 14 holes... is this a way to halt the usage of the older models? or is this unit damaged or fake?


your input is greatly appreciated
CAPONE
Junior Member
Posts: 5011
Joined: Sat Dec 27, 2008 3:25 pm

Post by CAPONE »

JDMEGKOUPE wrote:Image

Uploaded with ImageShack.us

im using a usbbdm original, not usbjtag nt, usbjtag, or usbbdm nt... can the original model work?

quick question, i borrowed this tool from a friend and now that u ALL pointed it out... why does it come up as an old BDM in the usbjtag software but it clearly has 14 holes... is this a way to halt the usage of the older models? or is this unit damaged or fake?


your input is greatly appreciated
Not with the New Software.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

14 pin is NOT old USB BDM. It is OLD USB JTAG. So it will not work period.
The old USB BDM will work with new NT software.
JDMEGKOUPE
Junior Member
Posts: 19
Joined: Mon Jul 26, 2010 12:41 pm

Post by JDMEGKOUPE »

thanks 2 all! time 4 a new programmer.
Locked

Who is online

Users browsing this forum: No registered users and 3 guests