Ok, I have experienced some strange behavior behavior similar to another post... This is what I observed:
-reset 1
-R
-init
-flshdct code
Found Intel 28F800C3
-getram dipcode
-getram code
-getram nvram
-getram ram
-save dipcode
-save code
-save dipcode
-save nvram
-save ram
PPV Info
Firmware Test 07.96
Do not forget to program the chip
UPM
Do not forget to set the NVRAM
-program code
Erase starts...
Erase time 00:00:00
Program starts...
Program speed 340.67 KB/s
Program time 00:00:06
Program pass
-program code 406000 aa000
Erase starts...
Erase time 00:00:00
Program starts...
Program speed 340.67 KB/s
Program time 00:00:06
Program pass
-setram nvram
This is similar to the problem experienced by by mr. sky. I have worked with A LOT of boxes, and this is the first time I have ever encountered this sort of behavior. As a result, the code is segment is corrupted and the nvram is out of whack too..when it powers on ther is the classic "0" in the LED display. These are the two lines from the flash.def file:
0x0089,0x88C1,Intel 28F800C3 ,0x100000,1,8,0x2000,15,0x10000
0x0089,0x8893,Intel 28F800B3 ,0x100000,1,8,0x2000,15,0x10000
Any ideas or is it just a bad flash chip perhaps? The box seemed to work fine when it was brought to me.
Strange behavior fron a NonPH
-
- Junior Member
- Posts: 108
- Joined: Thu Feb 01, 2007 6:13 pm
- Location: Orion constellation
-
- Junior Member
- Posts: 8973
- Joined: Mon Jul 18, 2005 9:33 pm
-
- Junior Member
- Posts: 108
- Joined: Thu Feb 01, 2007 6:13 pm
- Location: Orion constellation
When you say bad boot, do you mean a bad dipcode image or something else? From what I can tell, the box was fine before I tried to program it..
What Should RPC and A7 show?
Does that differ by each box?
If they are not showing the correct values, is getting it to program as simple as just changing them?
What Should RPC and A7 show?
Does that differ by each box?
If they are not showing the correct values, is getting it to program as simple as just changing them?
-
- Junior Member
- Posts: 108
- Joined: Thu Feb 01, 2007 6:13 pm
- Location: Orion constellation
Thanks USBBDM.
I picked up another box. CR4 board this time. I have gleaned this information:
Platform- 8
Family - B
Model - 5D
Tuner - V860DL
RPC = 00000460
A7 = 00200400
When I try program code or program code 406000 aa000, I get a Program failed at 410000. I have never encounterd this before. No idea what the hell is going on. The board looks new too...fresh off ebay...not a speck of dust or dirt on it either. CR4 board.
I notice the diagnostic screen says the tuner type is "Analog". Last time I saw this, the nvram was not correct for that board. I notice the firmware version on this box is 7.83....
Is there perhaps additional security that needs to be circumvented?
I picked up another box. CR4 board this time. I have gleaned this information:
Platform- 8
Family - B
Model - 5D
Tuner - V860DL
RPC = 00000460
A7 = 00200400
When I try program code or program code 406000 aa000, I get a Program failed at 410000. I have never encounterd this before. No idea what the hell is going on. The board looks new too...fresh off ebay...not a speck of dust or dirt on it either. CR4 board.
I notice the diagnostic screen says the tuner type is "Analog". Last time I saw this, the nvram was not correct for that board. I notice the firmware version on this box is 7.83....
Is there perhaps additional security that needs to be circumvented?
Who is online
Users browsing this forum: No registered users and 3 guests