NonPH locking on erase?

Box hardware. Watchdog. Models.
Locked
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

First have you removed C105? If yes, setup VNC and I canhelp you out. These boxes are old and hard to find now.
ingeleo
Junior Member
Posts: 7
Joined: Sat Nov 24, 2007 6:58 pm

Post by ingeleo »

thank you very much, I changed the boxes

greetings.. ingeleo
palevac
Junior Member
Posts: 88
Joined: Fri Apr 11, 2008 5:45 pm

Post by palevac »

wiggim wrote:after reset 1
rpc 00000460
A7 00200400

I do reset 1
init
ldram 400000 (load backup)
flshdct code
program
destination 406000 size aa000 with intel chip

Erase starts... thats where it ends. I have tried setram code and it writes but don't actually write, program code 406000 aa000 same thing, program code same thing, program same thing. I have no idea what else to do.

left it go for over 5 hr and no change to the flash.

also tired an init directly before program and no difference.

-reset 1
-R
-init
-ldram 400000
-flshdct code
Found Intel 28F800C3
-init
-program
Erase starts...

where it hangs every time.

software v0.87 dcttest 0.241

i have non ph cr4 and 0 display trying to fix it. these commands went thru but still 0 on display what is wrong ...???? also c105 is removed ...
-reset 1
-R
-init
-ldram code
-flshdct code
Found Address= 00400000 STMicro M29W800AB
-program 406000 aa000
Erase starts...
Erase time 00:00:06 (.890)
Program Starts...
Program speed 152.10 KB/s
Program time 00:00:04 (.546)
Program pass, if no further programming needed, power off/on the target
-reset


a7 and rpc ffffffff status

then i tried
-reset 1
-R
-init
-ldram code
Flip Firmware
-flshdct code
Found Address= 00400000 STMicro M29W800AB
-init
-program 406000 aa000
Erase starts...
Erase time 00:00:06 (.109)
Program Starts...
Program speed 138.41 KB/s
Program time 00:00:05 (.250)
Program pass, if no further programming needed, power off/on the target
A7= 00200400

RPC = 00000460 and black and white diagnostic screen i have

can you plesa tell me what command i should use because any other command i saw for how to get 0 out box gets stuck on progrrammingafter 4th bar doesnt movw further????
palevac
Junior Member
Posts: 88
Joined: Fri Apr 11, 2008 5:45 pm

Post by palevac »

-reset 1
-R
-init
-getram 200000 40000
-d 234f09
-reset 1
-R
-init
-ldram 400000 ( loaded 0793tvr7304rSPI.zip)

Flip Firmware

-flshdct 400000
Found Address= 00400000 STMicro M29W800AB
-program 400000 200000
Erase starts...
Erase time 00:00:19 (.171)
Program Starts... getting stuck on programming cr4 n on ph A7= 00200400

RPC = 00000460 using bdmnt
usbbdm
Junior Member
Posts: 8962
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

Try to use "erase" and then "sprogram" to see if you can get it going.
Locked

Who is online

Users browsing this forum: No registered users and 7 guests