...no spoon feeding?

Post by **usbbdm** » Mon May 10, 2010 5:44 pm

Your RPC value is 460 so it must be an PH6/CR4 or even old non-ph.
Have you ever done any programming? If not try to select type II to program. Type II board need to flip the firmware before and after testing.

jimmy5150 · Post by **jimmy5150** » Mon May 10, 2010 5:50 pm

its cr4. I have never done any programmind... I choose option 5 which is type 2, but it just says not supported...

-getram code

Time 00:00:05 (.140)
-flipfirm

-firm
Firmware not supported
-flipfirm

Post by **usbbdm** » Mon May 10, 2010 6:01 pm

jimmy5150 wrote:its cr4. I have never done any programmind... I choose option 5 which is type 2, but it just says not supported...

-getram code

Time 00:00:05 (.140)
-flipfirm

-firm
Firmware not supported
-flipfirm

Exit the script. Then go to tools and check the version number, if failed try to flip the code. Maybe your firmware is very old.

jimmy5150 · Post by **jimmy5150** » Mon May 10, 2010 6:04 pm

where under tools do i check for version number? And what commands do I use to flip the code? Sorry total noob-

jimmy5150 · Post by **jimmy5150** » Mon May 10, 2010 6:46 pm

how can i update my firmware?

Post by **usbbdm** » Mon May 10, 2010 6:54 pm

jimmy5150 wrote:where under tools do i check for version number? And what commands do I use to flip the code? Sorry total noob-

Go to testing and file the option do display the version.

jimmy5150 · Post by **jimmy5150** » Mon May 10, 2010 7:06 pm

you totally lost me there. I see the dct2244 testing menu at the top but theres nothing about displaying the version on there.. nothing under the tools menu either.

jimmy5150 · Post by **jimmy5150** » Mon May 10, 2010 7:14 pm

in the about box it says dct 2000 test version 0.29...

Post by **usbbdm** » Mon May 10, 2010 7:21 pm

Do you have logmein setup? I can remoetly take a look. I bet your firmware is simply too old. And you should let the box plug in and allow your CC to upgrade the box. Anyway setup logmein and I can look remotely.
I am sorry the firmware version display is not implemented for DCT2224,

jimmy5150 · Post by **jimmy5150** » Tue May 11, 2010 6:50 am

I found the firmware version on the diagnostic screen... 7.96. Is that too old?

CAPONE · Post by **CAPONE** » Tue May 11, 2010 6:52 am

jimmy5150 wrote:I found the firmware version on the diagnostic screen... 7.96. Is that too old?

No thats good.

jimmy5150 · Post by **jimmy5150** » Tue May 11, 2010 6:54 am

hm... I wonder what it is I'm doing wrong.... i have a feeling its probobly something simple.

Post by **usbbdm** » Tue May 11, 2010 7:25 am

jimmy5150 wrote:I found the firmware version on the diagnostic screen... 7.96. Is that too old?

No it is good. And your firmware is good.
Did you cut the C105? Looks like you might not disable the watchdog.

jimmy5150 · Post by **jimmy5150** » Tue May 11, 2010 7:56 am

I took the whole capacitator off... the little brown thing in the middle of two other little brown things shown on the cr4 pics in the topleft menu<----

cherrymachine · Post by **cherrymachine** » Mon Jun 14, 2010 8:00 pm

be sure you have configured the software set for what you are testing. config, cable box or modem. and what model it is. 700. 2224 etc/

when loading a file, dont use the ldnvram, use the open folder upper left hand side.

also when using manual commands getram setram etc. be sure your out of menu mode.

hit the # for exit

USB JTAG

...no spoon feeding?

Who is online