Does USBJTAG (NT) work with VDV22 from vonage.
-
- Junior Member
- Posts: 7
- Joined: Sat Feb 25, 2012 5:12 pm
Does USBJTAG (NT) work with VDV22 from vonage.
I have a vonage vdv22 device ,i am looking to unlock it so that i can use it on my preferred sip provider.I want to know does usbjtagnt helps me in doing this?
The device i am talking about is this.
http://www.kmart.com/vonage-vdv22-vd-di ... 854396000P
The device i am talking about is this.
http://www.kmart.com/vonage-vdv22-vd-di ... 854396000P
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
This does not help. If you have one in hand an Post pictures of MOBO to find out If it has a jtag port for example, then we may be able to see if there any posibilities of being able to jtag this Unit.jtagntvdv22 wrote:I have a vonage vdv22 device ,i am looking to unlock it so that i can use it on my preferred sip provider.I want to know does usbjtagnt helps me in doing this?
The device i am talking about is this.
http://www.kmart.com/vonage-vdv22-vd-di ... 854396000P
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
VD22 should be the same as VD21 which I add support a few years ago. Check thisjtagntvdv22 wrote:I have a vonage vdv22 device ,i am looking to unlock it so that i can use it on my preferred sip provider.I want to know does usbjtagnt helps me in doing this?
The device i am talking about is this.
http://www.kmart.com/vonage-vdv22-vd-di ... 854396000P
http://www.usbjtag.com/jtagnt/voip/vdv21.php
-
- Junior Member
- Posts: 7
- Joined: Sat Feb 25, 2012 5:12 pm
-
- Junior Member
- Posts: 7
- Joined: Sat Feb 25, 2012 5:12 pm
I have been struggling to open the vonage box due to non-availability of proper tools.I am currently looking for security bits tamper-proof screw driver.
People who already opened the box might help me by posting a picture of the screw driver here and it would be great if you can let me know where can i get one in usa.
People who already opened the box might help me by posting a picture of the screw driver here and it would be great if you can let me know where can i get one in usa.
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
Use a small flat screw driver and insert in then you can open it. No need to use the special tool. If you do not have the right width tool, use a bigger one and file it to make it fit.jtagntvdv22 wrote:I have been struggling to open the vonage box due to non-availability of proper tools.I am currently looking for security bits tamper-proof screw driver.
People who already opened the box might help me by posting a picture of the screw driver here and it would be great if you can let me know where can i get one in usa.
-
- Junior Member
- Posts: 7
- Joined: Sat Feb 25, 2012 5:12 pm
Finally i could open the box as suggested by Admin.
The pic is here: http://vonagevdv22.blogspot.com/
I think as usbbdm said both vdv21 and vdv22 are same except for the display part.
The pic is here: http://vonagevdv22.blogspot.com/
I think as usbbdm said both vdv21 and vdv22 are same except for the display part.
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
Take a close look of those missing risistors.jtagntvdv22 wrote:Finally i could open the box as suggested by Admin.
The pic is here: http://vonagevdv22.blogspot.com/
I think as usbbdm said both vdv21 and vdv22 are same except for the display part.
-
- Junior Member
- Posts: 7
- Joined: Sat Feb 25, 2012 5:12 pm
-
- Junior Member
- Posts: 7
- Joined: Sat Feb 25, 2012 5:12 pm
Can you let me know if the red box i marked on the pic is the place we need to connect serial port,if yes can you let me know which of them are gnd,tx,rx and power.
http://vonagevdv22.blogspot.com/
http://vonagevdv22.blogspot.com/
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
That would be for Serial TTL Tool And with a Meter you can Measure out VCC(+) ang Ground. A bottom View of Board will let you see which pin is Ground... Then you can connect the tx and rx and check if it works, If not Switch the TX and Rx wires. It is Fairly Easy to figure Out.....jtagntvdv22 wrote:Can you let me know if the red box i marked on the pic is the place we need to connect serial port,if yes can you let me know which of them are gnd,tx,rx and power.
http://vonagevdv22.blogspot.com/
-
- Junior Member
- Posts: 8974
- Joined: Mon Jul 18, 2005 9:33 pm
You might need to JTAG to erase Vonage settings.jtagntvdv22 wrote:Can you let me know if the red box i marked on the pic is the place we need to connect serial port,if yes can you let me know which of them are gnd,tx,rx and power.
http://vonagevdv22.blogspot.com/
For serial port there is only 4 pins. One is GND and one is VCC, I always use try and error and should not take long to find the pins.
-
- Junior Member
- Posts: 7
- Joined: Sat Feb 25, 2012 5:12 pm
Who is online
Users browsing this forum: No registered users and 5 guests