u-Link NT to program ECU E38.
Moderator: justsomeguy
-
- Junior Member
- Posts: 11
- Joined: Sun Jul 26, 2020 5:13 pm
Re: u-Link NT to program ECU E38.
Looks great, about ready to order, but..
Will this work on an E38 that has corrupted flash already? I have the .bin file for the flash, just need to program it..
Will this work on an E38 that has corrupted flash already? I have the .bin file for the flash, just need to program it..
-
- Junior Member
- Posts: 8978
- Joined: Mon Jul 18, 2005 9:33 pm
Re: u-Link NT to program ECU E38.
As far as programming, the state of current flash does not matter.
-
- Junior Member
- Posts: 11
- Joined: Sun Jul 26, 2020 5:13 pm
Re: u-Link NT to program ECU E38.
Excellent, placing an order shortly.. thanks!!
-
- Junior Member
- Posts: 32
- Joined: Sun Dec 12, 2010 4:58 pm
Re: u-Link NT to program ECU E38.
Is this possible on the E39A as well?
-
- Junior Member
- Posts: 8978
- Joined: Mon Jul 18, 2005 9:33 pm
Re: u-Link NT to program ECU E38.
I have not seen this model. I think it is possible.
I am working on the slave CPU and I am 60% done.
I am working on the slave CPU and I am 60% done.
-
- Junior Member
- Posts: 32
- Joined: Sun Dec 12, 2010 4:58 pm
Re: u-Link NT to program ECU E38.
@usbbdm, I have both the usbjtag and NT devices. Is the new device necessary for automotive ECU use?
-
- Junior Member
- Posts: 8978
- Joined: Mon Jul 18, 2005 9:33 pm
Re: u-Link NT to program ECU E38.
Yes. USB JTAG NT does not have enough programmable IO pins to work on MPC55X CPUs.
-
- Junior Member
- Posts: 8978
- Joined: Mon Jul 18, 2005 9:33 pm
Re: u-Link NT to program ECU E38.
I have already done the work for slave CPU. Need a little bit clean up.
The new protocol is MC9SC32 BDM on u-link NT.
The new protocol is MC9SC32 BDM on u-link NT.
-
- Junior Member
- Posts: 8978
- Joined: Mon Jul 18, 2005 9:33 pm
-
- Junior Member
- Posts: 2
- Joined: Sun Jan 30, 2022 7:29 am
- Location: Ukraine
- Contact:
Re: u-Link NT to program ECU E38.
good day
While waiting for my ordered U-Link NT
I have a Hummer H2 (died on the go) inside the ecu ACDelco E38
Check the engine is not lit on the instrument panel.
There is no response from the block.on the table for obd.
Inside, when checking the voltage, everything seems to be there, but there is no response from the MPС561 processor.
Read the firmware from the flash.
I ask for help to compare or record the correct firmware.
I can't attach a file
While waiting for my ordered U-Link NT
I have a Hummer H2 (died on the go) inside the ecu ACDelco E38
Check the engine is not lit on the instrument panel.
There is no response from the block.on the table for obd.
Inside, when checking the voltage, everything seems to be there, but there is no response from the MPС561 processor.
Read the firmware from the flash.
I ask for help to compare or record the correct firmware.
I can't attach a file
Last edited by HSV on Sun Feb 13, 2022 1:04 pm, edited 1 time in total.
-
- Junior Member
- Posts: 2
- Joined: Sun Jan 30, 2022 7:29 am
- Location: Ukraine
- Contact:
Re: u-Link NT to program ECU E38.
I can't attach a file
-
- Junior Member
- Posts: 8978
- Joined: Mon Jul 18, 2005 9:33 pm
Re: u-Link NT to program ECU E38.
Send email to [email protected]
-
- Junior Member
- Posts: 1
- Joined: Sun Jul 30, 2023 5:44 am
Re: u-Link NT to program ECU E38.
Hello Everyone,
has one of you yet put in some effort to design a BDM Adapter to get rid of soldering the cables to the Board?
I have 6 E38 laying around that need electronic love...
Thanks
ElM
has one of you yet put in some effort to design a BDM Adapter to get rid of soldering the cables to the Board?
I have 6 E38 laying around that need electronic love...
Thanks
ElM
Who is online
Users browsing this forum: No registered users and 1 guest