dct2000 ph9 programing stock

djmikimbin · Post by **djmikimbin** » Wed Mar 03, 2010 10:20 am

using usbbdm-nt and 0.34a software
trying to fake uid on a dct2000 ph9 but programming got stock
this is what i did:

reset 1
init
getram code

go to dct2224 testing
firmware test
checkmark everything and add the 10 digits.

flshdct code
program code (After this step nothing happens)

need some help..

Post by **usbbdm** » Wed Mar 03, 2010 11:33 am

Do you have a good back up of your initial code?
What is "nothing happened"? It stopped when programming?

djmikimbin · Post by **djmikimbin** » Wed Mar 03, 2010 3:29 pm

usbbdm wrote:Do you have a good back up of your initial code?
What is "nothing happened"? It stopped when programming?

yes i have a good back up.
nothing happened: means the progress bar do not show nothing. I would like
you to remote my desktop and check what is hapening.

djmikimbin · Post by **djmikimbin** » Wed Mar 03, 2010 4:33 pm

usbbdm Really need your help

Post by **usbbdm** » Wed Mar 03, 2010 4:39 pm

djmikimbin wrote:usbbdm Really need your help

After 9:00pm pacific time see if I am in chat.

djmikimbin · Post by **djmikimbin** » Wed Mar 03, 2010 9:37 pm

im in the chat now an you please help me

Post by **usbbdm** » Wed Mar 03, 2010 11:21 pm

Fixed via remote support.
It turns out a bug exist in BDM NT code. I will update 0.34b soon.

antwandavis1 · Post by **antwandavis1** » Mon Feb 07, 2011 1:24 pm

I have a DCT2000 and i am trying to change or program remote change with
0.45b software with latest DLL i backup my nvram,boot, plat ,app,and flash,Could someone tell me the next step because I read the Plat and went to Dct2224 testing ,firmware test and Remote Change UPM/UID hit ok ,The software gives a message{ Do not forget to program the chip }Help Thanks in advance.

justsomeguy · Post by **justsomeguy** » Mon Feb 07, 2011 2:55 pm

antwandavis1 wrote:I have a DCT2000 and i am trying to change or program remote change with
0.45b software with latest DLL i backup my nvram,boot, plat ,app,and flash,Could someone tell me the next step because I read the Plat and went to Dct2224 testing ,firmware test and Remote Change UPM/UID hit ok ,The software gives a message{ Do not forget to program the chip }Help Thanks in advance.

where did you find a plat and app in a 2224?? are you sure about the model of that box?

what exactly are you trying to do?

CAPONE · Post by **CAPONE** » Mon Feb 07, 2011 2:59 pm

justsomeguy wrote:where did you find a plat and app in a 2224?? are you sure about the model of that box?

what exactly are you trying to do?

I was about to ask Same thing. LOL The DCT only had dip,code,nvram & ram. NO Boot,Plat or APP's.

junctionbox · Post by **junctionbox** » Mon Feb 07, 2011 3:31 pm

The seniors are riding hard newbies just take your time and research and read all your answers are in the site

justsomeguy · Post by **justsomeguy** » Mon Feb 07, 2011 3:33 pm

junctionbox wrote:The seniors are riding hard newbies just take your time and research and read all your answers are in the site

i wasn't trying to ride him...was just trying to figure out what model he actually had and what he was trying to do was all:D

antwandavis1 · Post by **antwandavis1** » Mon Feb 07, 2011 3:51 pm

:mad:On the bottom of Box it say DCT2000 and DCT2224/1661/ABCDEFG but now i have a bigger problem i think i brick it,because trying to look at the video and change the UPM/UID and now it keeps saying program starts and nothing is happen,but when i unplug it and plug it back up it flashes bEr 1 this was my pay box .

antwandavis1 · Post by **antwandavis1** » Mon Feb 07, 2011 4:04 pm

Sorry a Dct 2224 with a Ph9 board i was trying to put the remote change on it but now it F--k. Please Help Thanks

justsomeguy · Post by **justsomeguy** » Mon Feb 07, 2011 4:17 pm

antwandavis1 wrote::mad:On the bottom of Box it say DCT2000 and DCT2224/1661/ABCDEFG but now i have a bigger problem i think i brick it,because trying to look at the video and change the UPM/UID and now it keeps saying program starts and nothing is happen,but when i unplug it and plug it back up it flashes bEr 1 this was my pay box .

by pay box do you mean that you rent it from the cc? will it detect at all? what does it say when you detect? what do you mean program starts and nothing happens? you change the uid/upm with the remote now after you program the box.

what EXACTLY did you do to the box so far?

USB JTAG

dct2000 ph9 programing stock

dct2000 ph9 programing stock

Help

To the newbies

Help

Help

Who is online