help dct2224 cr4 board
-
- Junior Member
- Posts: 254
- Joined: Mon Nov 22, 2010 12:27 pm
help dct2224 cr4 board
i have a dct2224 cr4 board that im trying to block and when i do the getram code and go to dcttesting/firmware test it says not supported also if i do getram nvram and go to dcttesting/network address unit address is set to 000000000000000 i try to put 0000000000001000 and it gives me an error and the program closes also when i try to write the code it says detect flash type first but i loaded the nvram fine from another dct2224 ph8.
and please tell me if im right is this the line of the nvram where you change 01 01 to 01 03 or 00 00
01b460 if not wich one is it
and please tell me if im right is this the line of the nvram where you change 01 01 to 01 03 or 00 00
01b460 if not wich one is it
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
On Some of those Model Boxes You Must flip Firmware first then do the Testing then Flip once More before writing Back to Box.lafraga wrote:i have a dct2224 cr4 board that im trying to block and when i do the getram code and go to dcttesting/firmware test it says not supported also if i do getram nvram and go to dcttesting/network address unit address is set to 000000000000000 i try to put 0000000000001000 and it gives me an error and the program closes also when i try to write the code it says detect flash type first but i loaded the nvram fine from another dct2224 ph8.
and please tell me if im right is this the line of the nvram where you change 01 01 to 01 03 or 00 00
01b460 if not wich one is it
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
-
- Junior Member
- Posts: 254
- Joined: Mon Nov 22, 2010 12:27 pm
i think my problem is that usbjtagnt is not detecting the flash type because when i do the "flshdct code" command this happens
-flshdct code
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum ffff,ffff
-flshdct code
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum ffff,ffff
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
I didn't know you where using a USBJTAG NTlafraga wrote:i think my problem is that usbjtagnt is not detecting the flash type because when i do the "flshdct code" command this happens
-flshdct code
Unknown flash type!
Report these values http://www.usbjtag.com/vbforum ffff,ffff
Like USBBDM Said. It won't work fopr that Model Box. The USBBDM is Needed.
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
-
- Junior Member
- Posts: 254
- Joined: Mon Nov 22, 2010 12:27 pm
-
- Junior Member
- Posts: 254
- Joined: Mon Nov 22, 2010 12:27 pm
im so sorry for asking so much but its that im not sure about what i am doing this is what happens......
as you can see when i made the backup of this box it was with the usbbdm connected in a rong way so both code and nvram are bad and testing i wrote and nvram from a ph8 board and this one is cr4 nowi need to know if that does not make any diference respecting to the channels because now im missing some of them
as you can see when i made the backup of this box it was with the usbbdm connected in a rong way so both code and nvram are bad and testing i wrote and nvram from a ph8 board and this one is cr4 nowi need to know if that does not make any diference respecting to the channels because now im missing some of them
-
- Junior Member
- Posts: 254
- Joined: Mon Nov 22, 2010 12:27 pm
this is the backup i loaded on the cr4 board box it is from a ph8 board please take a look at the code and the nvram and tell me if they are good please
http://www.megaupload.com/?d=C4O60QYP
http://www.megaupload.com/?d=C4O60QYP
-
- Junior Member
- Posts: 5011
- Joined: Sat Dec 27, 2008 3:25 pm
Yes All Looks Good. However Im Not sure you can Use Info From a PH8 on a CR4 Board. I tryed the Code and NVRAM of a CR4 on a PH8 Board Yesterday and It didn't work.lafraga wrote:this is the backup i loaded on the cr4 board box it is from a ph8 board please take a look at the code and the nvram and tell me if they are good please
http://www.megaupload.com/?d=C4O60QYP
"If you give a man a fish you feed him for a day. If you teach a man to fish you feed him for a lifetime."
Who is online
Users browsing this forum: No registered users and 5 guests