DPQ3925 bricked

[softrend]

Copyright (C) 2010,2011,2012
USB JTAG NT 0.54
Target: SBG6580SPI
-flshdct 0
Found Address= 00000000 MX25L12805D

soldiers equal to sbg6580
I put 3.3 v to pin 2, then I can read the flash, but the image is damaged ( I think), when I put the image saved, the modem dont boot again. someone has a backup of this model?

[CAPONE]

Copyright (C) 2010,2011,2012
USB JTAG NT 0.54
Target: SBG6580SPI
-flshdct 0
Found Address= 00000000 MX25L12805D

soldiers equal to sbg6580
I put 3.3 v to pin 2, then I can read the flash, but the image is damaged ( I think), when I put the image saved, the modem dont boot again. someone has a backup of this model?

That seams to be same Flash as the TM802G For which I made and tested and XML. If Not It should not be Dificult to Make the XML For it since the Software Can ID the Flash Correctly. If the Same as TM802G you should have a 16MB BackUp.

[CAPONE]

According to DataSheet its a 128MB Flash so a New XML will be Needed to Properly Make a BackUp of Flash.

DENSITY & MODE:
12805D: 128Mb

Full DataSheet Here.

http://pdf1.alldatasheet.com/datasheet- ... 2805D.html

[softrend]

this is my backup.
I think it is not good

[CAPONE]

this is my backup.
I think it is not good

YES Its Not a Good Read. Its 16MB and According to Datasheet this Flash is 128MB's. The Only thing you Need is the Proper XML to Read the Full 128MB Flash Then Read the Full Flash of a Good One to Fix this Bricked One. Once you can do a full read, I would bet its Just a Matter of writing the Boot Sector and the Target should be Un Bricked with all Original INFO Intact.

[merkin]

According to DataSheet its a 128MB Flash so a New XML will be Needed to Properly Make a BackUp of Flash.

DENSITY & MODE:
12805D: 128Mb

Its 128 megabit flash which is 16 megabytes

[softrend]

USBBDM, with this info, you can help me to write an xml for DPQ3925?

CM/Flash> show
Flash Device Information:

CFI Compliant: no
Command Set: Generic SPI Flash
Device/Bus Width: x16
Little Word Endian: no
Fast Bulk Erase: no
Multibyte Write: 256 bytes max
Phys base address: 0xbadf1a5
Uncached Virt addr: 0x1badf1a5
Cached Virt addr: 0x2badf1a5
Number of blocks: 257
Total size: 16777216 bytes, 16 Mbytes
Current mode: Read Array
Device Size: 16777216, Write buffer: 256, Busy bit: ☺

Size Device Device Region
Block kB Address Offset Offset Region Allocation
----- ---- ---------- ----------- --------- -----------------
0 32 0x1badf1a5 0 0 Bootloader (32768 bytes)
1 32 0x1bae71a5 32768 ??? {unassigned}
2 64 0x1baef1a5 65536 0 Permanent NonVol (65536 bytes)
3 64 0x1baff1a5 131072 0 Image1
4 64 0x1bb0f1a5 196608 65536 Image1
5 64 0x1bb1f1a5 262144 131072 Image1
6 64 0x1bb2f1a5 327680 196608 Image1
7 64 0x1bb3f1a5 393216 262144 Image1
8 64 0x1bb4f1a5 458752 327680 Image1
9 64 0x1bb5f1a5 524288 393216 Image1
10 64 0x1bb6f1a5 589824 458752 Image1
.
.
.
.
.
.
.
122 64 0x1c26f1a5 7929856 7798784 Image1
123 64 0x1c27f1a5 7995392 7864320 Image1
124 64 0x1c28f1a5 8060928 7929856 Image1
125 64 0x1c29f1a5 8126464 7995392 Image1
126 64 0x1c2af1a5 8192000 8060928 Image1
127 64 0x1c2bf1a5 8257536 8126464 Image1
128 64 0x1c2cf1a5 8323072 8192000 Image1 (8257536 bytes)
129 64 0x1c2df1a5 8388608 0 Image2
130 64 0x1c2ef1a5 8454144 65536 Image2
131 64 0x1c2ff1a5 8519680 131072 Image2
132 64 0x1c30f1a5 8585216 196608 Image2
133 64 0x1c31f1a5 8650752 262144 Image2
134 64 0x1c32f1a5 8716288 327680 Image2
135 64 0x1c33f1a5 8781824 393216 Image2
136 64 0x1c34f1a5 8847360 458752 Image2
137 64 0x1c35f1a5 8912896 524288 Image2
138 64 0x1c36f1a5 8978432 589824 Image2
139 64 0x1c37f1a5 9043968 655360 Image2
.
.
.
.
.
250 64 0x1ca6f1a5 16318464 7929856 Image2
251 64 0x1ca7f1a5 16384000 7995392 Image2
252 64 0x1ca8f1a5 16449536 8060928 Image2
253 64 0x1ca9f1a5 16515072 8126464 Image2
254 64 0x1caaf1a5 16580608 8192000 Image2 (8257536 bytes)
255 64 0x1cabf1a5 16646144 0 Dynamic NonVol
256 64 0x1cacf1a5 16711680 65536 Dynamic NonVol (131072 bytes)

CM/Flash>

[usbbdm]

What size of the flash for DPQ3925? What is your purpose to have the "right" XML? You want to program the individual segment?

[softrend]

First, I want to recover my bricked unit, from another working unit
second, write non-vol

[CAPONE]

First, I want to recover my bricked unit, from another working unit
second, write non-vol

The posted backup is No Good, If you wrote that to your bricked unit, you just further Bricked It and you compleatly 00ed out the flash. At this point al you can do to fix Bricked is a Full Clone as you already eliminated the OEM CERTS By zeroing out the Flash without a Good BackUp.

[FoxHazard]

CAPONE,
could you help me, I need the spi mode of your Cisco 3825, I'm sure it's the same for my dpc 3925, I'm from Brazil if he can send to my email you already sent by Private ... Thanks for listening ...
If anyone has any news of the DPC 3925 please help me out by MP Thanks to All ...