sb5100 help

SB5XXX,SBV5XXX
Locked
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

sb5100 help

Post by santino »

Ever since I bought the usb jtag cable I have followed procedure that you have which is.
Program Sigma
detect
ldram boot select the sigma boot
ldram image0 Select sigma application
program boot
program image0

When I do the following I get a dead modem please I need some help.
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

Post by santino »

yes I can still detect my modem
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

Post by santino »

sigmax-bl_v2.6-lite thats the bootloader i used
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

Post by santino »

question when I install the bootloader then it says reboot to change file do I have to reboot modem then program the regular file and reboot again?
usbbdm
Junior Member
Posts: 8708
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

santino wrote:question when I install the bootloader then it says reboot to change file do I have to reboot modem then program the regular file and reboot again?
Only if you use "sprogram" you need to reboot to use normal "program" command. Always use "cmpram" command to make sure what you have programmed is right.
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

Post by santino »

This is what I get when I use the cmpram -cmpram boot
Compair data OK
-cmpram image0
Compair data Failed address 9FC10008,target 42,PC memory 45

what does that mean? what should I do?
this is the steps I use
Program Sigma
detect
ldram boot select the sigma boot
ldram image0 Select sigma application
program boot
program image0
usbbdm
Junior Member
Posts: 8708
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

santino wrote:This is what I get when I use the cmpram -cmpram boot
Compair data OK
-cmpram image0
Compair data Failed address 9FC10008,target 42,PC memory 45

what does that mean? what should I do?
this is the steps I use
Program Sigma
detect
ldram boot select the sigma boot
ldram image0 Select sigma application
program boot
program image0
Your image0 does not program properly.
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

Post by santino »

Ok I programed again and now I get only the first light blinking???????????????????????
usbbdm
Junior Member
Posts: 8708
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

santino wrote:Ok I programed again and now I get only the first light blinking???????????????????????
Have you one the cmpram and verified OK?
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

Post by santino »

detect
IDCODE 334817F
Broadcom BCM3348
IMPCODE 800908
DMA supoorted
Found Address= 9fc00000 Intel 28F160C3B
-ldram boot
-ldram image0
-program boot
Erase starts...
Erase time 00:00:00 .014
Program speed 131.07 KB/s
Program time 00:00:00 .084
Program pass, if no further programming needed, power off/on the target
-program image0
Erase starts...
Erase time 00:00:08 .022
Program speed 136.72 KB/s
Program time 00:00:07 .032
Program pass, if no further programming needed, power off/on the target
-cmpram boot
Compair data OK
-cmpram image0
Compair data OK
THATS WHAT I GET.............................and still the first light only blinking.
usbbdm
Junior Member
Posts: 8708
Joined: Mon Jul 18, 2005 9:33 pm

Post by usbbdm »

Well your JTAG works just fine. Then it is a matter of the firmware. You need consult someone who has experience with Sigma. I am not expert of Sigma. You might need to configure the firmware. Other sites should have information you want. Where do you download the Sigma from? I heard certain version Sigma needs certificate to work but not sure.
santino
Junior Member
Posts: 197
Joined: Wed Jul 19, 2006 4:50 pm

Post by santino »

ok thanks for your help
nunny
Junior Member
Posts: 122
Joined: Mon Feb 05, 2007 7:33 pm
Contact:

Post by nunny »

yes the sigma x2 origina from tcniso need certificate to work but there is a cracked version out there that works with out it and has some fixes
andak
Junior Member
Posts: 27
Joined: Tue Jul 26, 2005 3:17 am

Post by andak »

Try this Theoryshare download section. I think the SB5100 Stealth Editon 13.005 is a cracked SIGMA-X2.
junctionbox
Junior Member
Posts: 449
Joined: Sat Oct 21, 2006 6:19 am

THE HELP DOCTOR DING DONG

Post by junctionbox »

POOR SOUL to clear your 5100 first just write command rest51 then wait 15 minutes then make sure you down load sigma bootblocker sigma 1.06 use commands detect writesigma the first to highlite is the bootblocker apply once 2nd 1.06 sigma apply twice go to web page disable all but baseline privacy
Locked

Who is online

Users browsing this forum: No registered users and 0 guests